| Author |
 Replies: 10 / Views: 705 |
|
|
Pillar of the Community
United States
2286 Posts |
|
|
|
|
Bedrock of the Community
 United States
18757 Posts |
Can you tell if it's actually FBL? I'm not sure if we could verify that with pictures because of the scuffing on the slab.
Inordinately fascinated by bits of metal with strange markings and figures
|
|
Pillar of the Community
 United States
1343 Posts |
First I don't know much about this, but I did a quick ebay sold listings search and I don't believe the ICG slab increases the value much if at all. I found a few ICG slabbed coins similar to yours (MS64 FBL) that sold for around $50-$55, and a raw coin that someone took really good pictures of and claimed it was MS63+ (according to him/her) that sold for $79.00.  |
|
Pillar of the Community
 United States
2286 Posts |
|
|
Pillar of the Community
United States
7057 Posts |
Greysheet doesn't even list a value for MS 63 FBL. The closet is MS 64 FBL at $50, the MS63 coin is $23. Neither of these are lofty values, so do what makes sense to you. Personally I don't pay for slabs so I would be looking at around greysheet ($23) to buy this coin, (please note I don't collect this series, so take that into consideration). The value on these only gets high after MS66 FBL. Edited to add:ICG is a reputable TPG but since they along with ANACS don't have a Registry set, there usually isn't much added premium for a coin in an ICG slab. Edited by hfjacinto
02/21/2025 3:15 pm
|
|
Pillar of the Community
United States
1952 Posts |
If it's just that the slab is scuffed, you could try polishing it with PlastX (or similar).
|
|
Pillar of the Community
United States
2286 Posts |
Quote:
If it's just that the slab is scuffed, you could try polishing it with PlastX (or similar) There's a couple of deeper scratches as well.
|
|
Pillar of the Community
United States
1871 Posts |
It tried Novus polishing compound, 1, 2, 3 grades on a coin slab. I worked on it for over an hour, didn't make much difference. Maybe I quit too soon. Those slabs seem pretty hard. Deep scratches likely can't be removed with polishing.
It's rather frustrating to buy a new coin recently slabbed from a dealer and there's already light scratches on the slab.
Edited by livingwater
02/21/2025 4:59 pm
|
|
Moderator
United States
72197 Posts |
polishing the slab is a good idea you may not get them all off, you can clear it us to some degree.
|
|
Pillar of the Community
United States
1862 Posts |
ICG really isn't a well respected TPG compared to the top 3. The PCGS site has a $60 value on MS-63FBL in a PCGS slab. You could crack it out and put it in a self slab such as the lighthouse slabs or try to polish the lens of the ICG slab as others have suggested. I know from auto headlight restoration that you can wet sand the plastic lens down to 2000 grit and then spray it with UV clear coat. Either way I suggest purchasing some of the clear sleeves to prevent any of your slabbed coins from such damage in the future. |
|
Pillar of the Community
United States
7190 Posts |
Quote:
I know from auto headlight restoration that you can wet sand the plastic lens down to 2000 grit and then spray it with UV clear coat. Either way I suggest purchasing some of the clear sleeves to prevent any of your slabbed coins from such damage in the future. Great suggestion.
|
| |
Replies: 10 / Views: 705 |
|
Posted 02/21/2025 1:11 pm
