| Author |
 Replies: 16 / Views: 7,516 |
Page 2 of 2
|
|
|
|
Bedrock of the Community
United States
12057 Posts |
Excellent example of a tough variety. Also looks like an OMM, but that may be die subsidence. Love the VLDS with the flowlines, clear trails, and right wing crack. I find it interesting that neither of the two usual obverse cracks for this series are present, although it looks like the lower bust crack may be there but perhaps has been covered up a bit by the extensive die polishing.
Member ANA - EAC - TNA - SSDC - CCT #890 "Most of the things worth doing in the world had been declared impossible before they were done." -- Louis D. Brandeis |
|
Pillar of the Community
Canada
891 Posts |
That is real nice  |
|
Pillar of the Community
 United States
3058 Posts |
Wow! Awesome find! I am with coinmasters on this one!
Edited by coinlover1899
03/18/2017 09:18 am
|
|
Bedrock of the Community
United States
62064 Posts |
Not re-engraved. Just a case of a VLDS die that struck this coin. The heavy die flow is obvious.
|
|
Pillar of the Community
 United States
2376 Posts |
Sorry Coop but it is Fs-901
|
|
Pillar of the Community
United States
2376 Posts |
I normally am opposed to thge use of others images but I am crediting the bottom image to the PCGS site linked above. This set of pics showes my coin on top and the attribured 901 on the bottom. The same die just different stages  |
|
Bedrock of the Community
United States
12057 Posts |
My opinion would be that OP's coin is a later die state strike from the modified/re-engraved dies, where die erosion has weakened the area in question again. Traces of the die gouges, i.e. the re-engraving, can still be seen in the gap below the bottom arrow shaft, faint, but present.
Member ANA - EAC - TNA - SSDC - CCT #890 "Most of the things worth doing in the world had been declared impossible before they were done." -- Louis D. Brandeis |
|
Bedrock of the Community
United States
62064 Posts |
The location of the mint mark does match the correct die number. All I could see was the heavy die flow on this one. I was not aware of the re-engraving on this die. (I know it now)
|
|
Pillar of the Community
United States
745 Posts |
Tim Hughes
Edited by Onedollarbillnut
08/19/2017 7:59 pm
|
|
Pillar of the Community
5464 Posts |
I like the coin. I love your pictures!! |
|
Bedrock of the Community
United States
74639 Posts |
Sorry Coop. But you're wrong. It is a re engraved die. I looked on the link and it matches it. You're only right on one thing. That is the coin being in a Very Late Die State (VLDS)
Errers and Varietys.
Edited by Errers and Varietys
08/19/2017 9:39 pm
|
|
Pillar of the Community
United States
7516 Posts |
stoneman,it is a beautiful variety,love the flowlines, I think there may be a nice clashed die below the Beak as well,this coin has got a lot going on with it |
|
Bedrock of the Community
United States
74639 Posts |
|
|
Pillar of the Community
United States
745 Posts |
Just got word from ANACS it is a MS-64
Tim Hughes
|
|
Pillar of the Community
United States
2376 Posts |
I guess just to clarify, Onedollarbillnut's coin is not the one I started this thread with ( Nice coin you have there! )
I still have mine and have not sent it anywhere.
|
|
Page 2 of 2
|
Replies: 16 / Views: 7,516 |
Page 2 of 2
|
First Page
Posted 03/18/2017 01:06 am
