| Author |
 Replies: 17 / Views: 2,980 |
Page 2 of 2
|
|
|
|
Pillar of the Community
 United States
1215 Posts |
The marks are not recessed.
|
|
Pillar of the Community
7234 Posts |
Quote:
your coin is a cast copy That or an extremely worn die with those surfaces. Who knows what those little black things are. If it is a cast coin then those black things were in the poured metal and now are part of the "coin". Can you get a weight on it? Edited by Mark1959
03/24/2017 9:56 pm
|
|
Pillar of the Community
United States
1215 Posts |
THE COIN IS 100% GENUINE.
|
|
Rest in Peace
10197 Posts |
Your coin appears dipped in an acid based cleaner. That has removed some microscopic crud and surface metals. Your coin contains only .0715 oxz of silver the rest is a mix. Certain acids react with only certain metals. Looks like you have either a direct reaction to this or it's the residual that the dip didn't eat off.
BTW, are you 100% sure?
|
|
Pillar of the Community
United States
5209 Posts |
What is the 100% weight of the coin.  |
|
Pillar of the Community
United States
1119 Posts |
Quote:
Your coin contains only .0715 oxz of silver what? |
|
Pillar of the Community
United States
6370 Posts |
Quote:
I'm no expert on this but I'm still convinced more now than earlier that your coin is a cast copy .
Hope I'm wrong . Explain to me how a cast coin can get coin luster, and I would be more inclunid to agree with you. If you can't, then I would rethink your hypothesis. There are die flow lines as well as polishing lines, both of which are of small enough resolution to be lost in the casting process. I am seeing a genuine coin here with metallurgical anomalies, whether that be a strikethrough or impurities in the metal. |
|
Moderator
 United States
56855 Posts |
How did you try to remove the black? John1  |
|
Rest in Peace
United States
18456 Posts |
Quote:
If it is a cast coin then those black things were in the poured metal and now are part of the "coin". Can you get a weight on it? Why would this be impossible ? Quote:
Explain to me how a cast coin can get coin luster Could it be possible a very light polishing compound and a very light wheel was used for a couple of seconds on each side ? Hey I'm just throwing things at you guys so we can get to the bottom of this and find out for sure what's up with this coin .  |
|
Pillar of the Community
United States
6370 Posts |
Quote:
Could it be possible a very light polishing compound and a very light wheel was used for a couple of seconds on each side ?
Hey I'm just throwing things at you guys so we can get to the bottom of this and find out for sure what's up with this coin . No. Polishing a cast coin will not give it coin luster (cartwheel luster). What you are talking about is whizzing, and that is completely different. I am talking about die flow lines (the essence of luster), which I can clearly see on the OP's coin. |
|
Pillar of the Community
United States
5833 Posts |
The coin is genuine!
I am thinking along in the line of carbon toning for lack of proper term? Its almost seem like it was environmental build up and not stored properly.
|
|
Pillar of the Community
United States
1757 Posts |
I know the answer ...
John Lorenzo
Numismatist
United States
|
|
Bedrock of the Community
United States
17884 Posts |
|
|
Moderator
United States
189340 Posts |
Quote:Quote:
I know the answer ... John Lorenzo Numismatist United States Enlighten us. Yes, please!  |
|
Pillar of the Community
United States
5833 Posts |
|
|
Page 2 of 2
|
Replies: 17 / Views: 2,980 |
Page 2 of 2
|
First Page
Posted 03/24/2017 9:55 pm
