| Author |
 Replies: 19 / Views: 2,795 |
Page 2 of 2
|
|
|
|
Pillar of the Community
  United States
1551 Posts |
Yep there are different types that had been "repaired" at the mint. Or so the story go's, I have seen about 4 of them total and this was the best one I found so I bought it.
Some of the tic's and bumps do nothing for me, but some types are just cool!
|
|
Pillar of the Community
3660 Posts |
I have a hard time with online photos in the differentiation of raised or recessed....It looks raised to me.....I have seen other coins where portions of the previous planchet struck actually stuck temporarily to the die and came off as a cap to the next to the next planchet.....and that thing about different types causes me to wonder.....I will tell you that I am not buying the story about it being a die repair job though....whatever....Super cool coin Russ...  |
|
Moderator
 United States
23522 Posts |
That one little spot of the Morgan dollar die is worth its' own independent study. 1878 is the most prominent year for anomalies, but over the years of production all sorts of interesting things have popped up between the eagle's right wing and leg. This one is particularly interesting. It looks like melting, but you'd need temps in excess of 1700F for that to happen. Even if someone had made that mistake in the annealing process, why there rather than a more pointed part of the die, where one would assume spot temperatures would be higher? Fascinating. |
|
Pillar of the Community
United States
1551 Posts |
I wonder about that as well. There are 4 types of funky feather 1878 S Vams all are very different. The earlier the state to me the cooler they look. As for what was the cause I do not know. The 1878 S coins did have a lot of repair or touch ups done on the eagle.
They are neat almost as if someone was sweating in a copper pipe and a drip of molten solder dropped on a coin.
|
|
Pillar of the Community
United States
3076 Posts |
I think its using chamell #9....
looks like a soldering 101 class experiment...gone wild
|
|
Moderator
United States
23522 Posts |
Russ, can you get the whole length of this anomaly with your nice detail shots? The first detail pic is great; a series of those, all the way up (even if it takes 6 separate shots) would be cool. I want to stitch them together to contemplate the whole thing at once.
|
|
Pillar of the Community
3660 Posts |
Uh Oh....the notion of extra pictures sounds like it could compel me to speculate out the wrong end again.
|
|
Moderator
United States
23522 Posts |
Speculation is constructive, regardless of the origin.
|
|
Pillar of the Community
United States
1551 Posts |
Give me a few And your wish is my command
|
|
Pillar of the Community
United States
1551 Posts |
|
|
Pillar of the Community
3660 Posts |
If this were caused by a capped die, then I might think that there could be a slight progression displayed between successively struck coins....however, it might also imply that there should be a coin stuck that is missing a good portion of planchet metal in the same area....I am still in la la position on this one.....but I am fairly certain that no self respecting engraver would call this a patch job worthy of submission to the coining room....it is in a device, and was not done in the coining room by polishing.
|
|
Pillar of the Community
United States
1551 Posts |
Edited by twohawks
12/12/2010 7:34 pm
|
|
Pillar of the Community
3660 Posts |
Whiskey, gin and beer......simply dreadful.....haven't you guys ever heard of wine? Those San Fransico mint workers could not have been so unrefined as to depend on lesser spirits to steady their nerves could they?
|
|
Pillar of the Community
United States
3076 Posts |
well I see its sure put a smile on your face!  |
|
Pillar of the Community
3660 Posts |
Wheewooh, I thought that I was looking in the mirror there for a minute, til I remembered that my teeth are straighter and whiter than that....I 'have' been referred to as a little hefer by someone that I will never speak to again.
|
|
Page 2 of 2
|
Replies: 19 / Views: 2,795 |
Page 2 of 2
|
First Page
Posted 12/12/2010 1:13 pm
