| Author |
 Replies: 18 / Views: 3,356 |
Page 2 of 2
|
|
|
|
Pillar of the Community
Canada
1747 Posts |
a counter stamp is when someone stamps a coin, usually with a letter punch or maybe a small logo. This is done post minting and is more regarded as damage than anything else. There is collectors of older counter stamped coins.
however your coin to me looks like the radioactive part looks to be raised from the coin, is this correct? Can we get a picture of the other side, and perhaps images from an angle?
|
|
New Member
 United States
10 Posts |
It is raised, that"s how I found it. Based on the lines that are across it diagonal, bottom right to top left, the mark appears to be from the original pressing. Kind of like "lands and grooves" from a bullet comparison. Just an observation. I will try capture a side view to show how high it is, then post again. Thanks.
|
|
New Member
United States
10 Posts |
A little blurry. I'll try again in a few
|
|
Pillar of the Community
United States
2023 Posts |
Looks to me like half of a snap/button -- there appears to be some extra metal, as though it were soldered on.
|
|
Rest in Peace
United States
7075 Posts |
Looks like extra metal to me, too. It looks like it was pounded into the dime. The perimeter looks like metal that was in the way.
Someone messing around at the machine shop, maybe?
|
|
New Member
United States
10 Posts |
|
|
New Member
United States
10 Posts |
working on getting 2 new photos out. I can see no other metal, and the faceside has no distortion as if the opposite said had been hit hard. trying to figure this system out to get the photos out to you all. Thanks for checking them out
|
|
New Member
United States
10 Posts |
Here is the backside again, different angle  |
|
New Member
United States
10 Posts |
Here is the face side. I see nothing to indicate any force or pounding, or stamping the metal onto the coin.  |
|
Moderator
 Australia
16868 Posts |
Yep, someone, for whatever reason, decided to turn an ordinary dime into a button by soldering a loop onto the back. His was then broken off again.
This is a very common occurrence on older silver and gold coins. I've not seen anyone attempt it on a modern coin, especially a clad one.
It might even be simply glue. Clear resin glues can look like a piece of metal when stuck to a coin.
Either way, it is not a mint error.
Don't say "infinitely" when you mean "very"; otherwise, you'll have no word left when you want to talk about something really infinite. - C. S. Lewis
|
|
New Member
United States
10 Posts |
I did note one thong, The side that has the anomaly is still very shiny, as if it had not touched any other surface. Its like the raised metal had kept the rest of the side from contact with other items/ coins flesh etc.
|
|
New Member
United States
10 Posts |
Could the apparent Soldering be from the pressing if there was residue left on the stamp from a previous pressing. I did notice the shape marking to be similar to the snap button, but its way to small. It's maybe 1 to 2mm at most.
|
|
Pillar of the Community
United States
4212 Posts |
|
|
Rest in Peace
United States
17900 Posts |
The extrusion is damage, no matter the reason it was applied.
|
|
Rest in Peace
United States
7075 Posts |
Quote:
Could the apparent Soldering be from the pressing if there was residue left on the stamp from a previous pressing. I did notice the shape marking to be similar to the snap button, but its way to small. It's maybe 1 to 2mm at most. I don' think so. Here's a site that will give you more info. on what to look for -- maybe you've already been there... http://www.error-ref.com/?s=struck&...s+error |
|
Page 2 of 2
|
Replies: 18 / Views: 3,356 |
Page 2 of 2
|
First Page
Posted 11/25/2016 2:25 pm
