| Author |
 Replies: 44 / Views: 4,000 |
|
|
|
Rest in Peace
10197 Posts |
Zack, If it was stamped onto the coin, it would leave an indention when falling off and would be even with the field, soak it, if it is plastic or tape will loosen and come off.
|
|
Pillar of the Community
 United States
1901 Posts |
I wouldn't need to soak anything because the spot I am pointing out is peel8ng off I will bend it and take a picture when I get home from work so you guys understand what I am trying to show you
|
|
Bedrock of the Community
United States
94367 Posts |
Not soaking it makes no sense to me.  |
|
Pillar of the Community
United States
1901 Posts |
Look at the picture I labeled on top and under look at the edge of the lifted metal and it is jagged. That is lifted metal.and why would I need to soak it? When I can peel off the peeling metal without soaking?
|
|
Bedrock of the Community
United States
62064 Posts |
I would not soak it. It might just peel off. You might need some "Goo Be Gone" or some other tape to remove the sticky residue? Use a glove when touching the surface of the coin or hold by the edge of the coin.
|
|
Valued Member
United States
97 Posts |
Mrzllewellyn -- I will again agree with you. I refer to your error as delamination (because the material is separating from the coin.) I have looked at enough similar pieces to agree with you. One reason for others' disagreement is your original photographs made the material look distinctly different from the rest of the coin, which of course made the delam look like foreign material. Your later pictures clearly show the thin lifted section of copper. An yes, there will be subdued details of the design underneath the delamination, which I find quite often under missing or folded delamination. The thinner the delam, the more detail transfers through. I like your coin.  |
|
Pillar of the Community
United States
1901 Posts |
|
|
Valued Member
United States
150 Posts |
That is one interesting piece: Kind-ah looks like an in-bedded sliver during original plate rolling prior to planchet punching process.
Small sliver of sheered material rolled in to?
Not a lamination error but foreign material but the same old copper?
coop you can see the line in the stem what's it look like to you.
Looks like it OldMoney
Edited by FrankenCoin
04/13/2018 02:13 am
|
|
Bedrock of the Community
United States
75224 Posts |
Guys, it is a Lamination error, not tape or glue. No need to soak it in Acetone. Nice find!  Errers and Varietys.
|
|
Pillar of the Community
United States
2563 Posts |
An obvious lamination error from the updated photos. Nice find!
|
|
Pillar of the Community
United States
1901 Posts |
|
|
Rest in Peace
10197 Posts |
Not a lam Zack, it is an adhered piece of struck debris. It is a struck thru, the indention proves that, just that that piece didn't fall off. Looks like a chunk of copper. A lamination is a planchet flaw, caused by alloy mix or annealing problems. There are no indications of any of those on this coin. Still an interesting error nonetheless.
Edited by Crazyb0
04/14/2018 01:06 am
|
|
Pillar of the Community
United States
1901 Posts |
Yeah that's why I had that struck through debris before but yeah thanks. I knew it was either lam or struck through debris retained.
|
|
Bedrock of the Community
United States
62064 Posts |
Well it is a lamination. Keep it safe with images like the ones you posted. Don't clean the coin, leave it as it is.
|
|
Pillar of the Community
United States
2624 Posts |
I work with rolled steel. I see lamination all the time. I have never seen lamination with such straight or parallel edges.
|
| |
Replies: 44 / Views: 4,000 |
First Page
Posted 04/12/2018 9:12 pm
