Could Someone Post A Close Up Picture Of "notching" On A Lincoln Memorial Cent / LMC Reverse?

To participate in the forum you must log in or register.

Author	Replies: 9 / Views: 909
Rabbithole1 Pillar of the Community United States 520 Posts	Posted 01/14/2019 8:57 pm Is the notching in always on the top corners of the devices? Do the "notches" or chuncks that are in the middle of a letter have anything to do with what you all call notching? And what would you consider a broken O, or an O that over loops itself. It's hard to explain, but kind-of like the end of a coil. Report this Post to the Staff

coop Bedrock of the Community United States 62064 Posts	Posted 01/14/2019 9:48 pm 1983 DDD-001 and 002: United: One: Cent EPU: Hope this helps. Report this Post to the Staff
tropicalbats Pillar of the Community United States 6116 Posts	Posted 01/14/2019 10:02 pm It's often not so dramatic, but it's there. Here is a 1964 Lincoln with notching. Report this Post to the Staff
coop Bedrock of the Community United States 62064 Posts	Posted 01/14/2019 10:06 pm 1964 WDDR-040 Report this Post to the Staff
coop Bedrock of the Community United States 62064 Posts	Posted 01/14/2019 10:10 pm 1963 DDR-007 Proof cent Report this Post to the Staff
Rabbithole1 Pillar of the Community United States 520 Posts	Posted 01/14/2019 10:13 pm You guys are Awesome!! Thank you!! Report this Post to the Staff
coop Bedrock of the Community United States 62064 Posts	Posted 01/14/2019 10:17 pm I have thousands more. Just noticed my post count. Won't be long until a new number will show up: I know what your thinking... Edited by coop 01/14/2019 10:33 pm Report this Post to the Staff
Rabbithole1 Pillar of the Community United States 520 Posts	Posted 01/14/2019 10:38 pm OK, fingers crossed. Do you all consider this notching on my 1964p LMC. Report this Post to the Staff
Rabbithole1 Pillar of the Community United States 520 Posts	Posted 01/14/2019 11:06 pm And I do see a break in the O on some of your pictures Coop. Kind-of like this one on mine. Report this Post to the Staff
coop Bedrock of the Community United States 62064 Posts	Posted 01/15/2019 02:51 am The question about the 'O' is coin damage. The clue is the incuse mark on that device. If it we a doubled die, then it would be raised, not sunk in on the device. Also the other areas are showing Machine Doubling. Note how the edges of those devices are affected? On the examples we posted, the spread is seen on the center of the devices, not on the edge. The edges will show you MD and die wear. Look at the centers of the devices, forget looking there. After reading this, go back over the images we posted. Note how the devices are showing spread or enlargement of the devices. Then look back again at your images and note that the devices you posted are normal sizes or reduced from what a normal device should be. Report this Post to the Staff
	Replies: 9 / Views: 909

To participate in the forum you must log in or register.

All Forums Category: US Coins and Currency Forums Forum: US Modern Variety and Error Coins

The First Dollar, your premier source for bullion and rare coins. See our bullion list on the site and the coin inventory on ebay.

Silver Gold Bull US is the United States leading bullion dealer. We deliver gold coins, gold bars, silver coins, silver bars and precious metals to your door. Order today!

View Last 100 New Topics

View Last 100 Active Topics

Disclaimer: While a tremendous amount of effort goes into ensuring the accuracy of the information contained in this site, Coin Community assumes no liability for errors. Copyright 2005 - 2026 Coin Community Family- all rights reserved worldwide. Use of any images or content on this website without prior written permission of Coin Community or the original lender is strictly prohibited.
Contact Us | Advertise Here | Privacy Policy / Terms of Use

Coin Community Forum

It took 0.34 seconds to rattle this change.

Could Someone Post A Close Up Picture Of "Notching" On A LMC Reverse?