| Author |
 Replies: 17 / Views: 2,429 |
Page 2 of 2
|
|
|
|
Moderator
 United States
34425 Posts |
Not dyslexia, but rather wishful thinking.  Keep at it though and you'll get a keeper (just not this one). "If you climb a good tree, you get a push."
-----Ghanaian proverb
"The danger we all now face is distinguishing between what is authentic and what is performed."
-----King Adz
|
|
Bedrock of the Community
United States
74578 Posts |
Quote:Not dyslexia, but rather wishful thinking.  Yep, we all have wishful thinking. Sometimes, we think it's something, but then we realize it's just our imagination.  Errers and Varietys.
|
|
Valued Member
 United States
492 Posts |
ok I sort of knew that would be the answer. I simply do not recognize doubling. And I study what is available. Yuk. Tks
|
|
Rest in Peace
United States
1559 Posts |
radatat, when you have a real doubled die in your hands you will know it. Trust me when I say that we have all been there! I for one must have posted over two dozen coins thinking, hoping that I had finally found one only to find out that I was wrong again. Don't let it discourage you as it takes time to learn and understand! keep doing your homework and research as well as searching and one will come your way. |
|
Bedrock of the Community
United States
74578 Posts |
Quote: Don't let it discourage you as it takes time to learn and understand! keep doing your homework and research as well as searching and one will come your way. I agree. I have been there too and it does take time to learn. It's not easy at first, but once you get good at it, you'll go through coin rolls like nothing. Don't give up and keep asking questions!  Errers and Varietys.
|
|
Bedrock of the Community
United States
94367 Posts |
Keep looking!  |
|
Rest in Peace
United States
17900 Posts |
You're keeping at it and asking the questions and posting good photos. You will be rewarded eventually  |
|
Rest in Peace
10197 Posts |
Radatat, remember that die wear and initial design are key factors in the size of details. For instance, the 1968 series Master Working Hub dies were so overworked that massive Die Deterioration was passed down through ALL dies used that year. It made the IGWT touch the rim and the L of Liberty to curl up the edge. Other years have similar problems, 1982 comes to mind where it was so bad they changed to the 1983 Hubs with smaller details. |
|
Pillar of the Community
United States
939 Posts |
I see just a tiny bit of what looks like md on the N, but that's it.
|
|
Pillar of the Community
United States
939 Posts |
Could I see close up shots of liberty? Try to get a close clear shot
|
|
Rest in Peace
United States
1559 Posts |
Coinfrog, your suppose to post your picture in the "Picture the Poster" thread! Edited by Tootallious
04/18/2018 7:30 pm
|
|
Valued Member
United States
492 Posts |
Coin Frog here is the best I can get of Liberty. Rich   |
|
Valued Member
United States
452 Posts |
I probably submitted pictures of 100 coins I was sure were doubled before I found some actual doubling. It's no joke, when you see the real deal it's like boing! Lol.
|
|
Pillar of the Community
United States
939 Posts |
Thanks sorry I was looking for something in the L and I but there is nothing.
|
|
Bedrock of the Community
United States
62064 Posts |
The master hub was replaced in 1969. The old master hub was spreading pushing the devices to the edge of the hub, creating issues with the master die, working hubs and working dies. The issue was progressing in prievious years. Now they needed to change on the new master hub. All the coins that year pretty much looked like your coin.
|
|
Page 2 of 2
|
Replies: 17 / Views: 2,429 |
Page 2 of 2
|
First Page
Posted 04/18/2018 4:17 pm
