Coin Community Family of Web Sites Join Thousands of Coin, Bullion, & Money Collectors
Specializing in Modern Numismatics Join Thousands of Coin, Bullion, & Money Collectors Shop for APMEX Bullion on eBay!300,000 items to help build your collection! Vancouvers #1 Coin and Paper Money Dealer Royal Canadian Mint products, Canadian, Polish, American, and world coins and banknotes. Coin, Banknote and Medal Collectors's Online Mall








Username:
Password:
Save Password
Forgot your Password?


This page may contain links that result in small commissions to keep this free site up and running.

Welcome Guest! Registering and/or logging in will remove the anchor (bottom) ads. It's Free!

A Tip For Getting Coins Into Tight Folders

To participate in the forum you must log in or register.
Author Previous TopicReplies: 5 / Views: 1,511Next Topic  
Valued Member
proofreader's Avatar
United Kingdom
216 Posts
 Posted 05/07/2014  04:53 am Show Profile   Bookmark this topic Add proofreader to your friends list Get a Link to this Message Number of Subscribers
I wanted to share a tip that I use to help me get coins into tight folders.

After some experimenting I found that placing the folder on top of a sheet of bubble wrap works very well.

There is just enough 'give' to enable the coin to be pushed in firmly.

I hope this helps if you are having trouble like I was.
Pillar of the Community
keepcalmandcoinon's Avatar
United States
865 Posts
 Posted 05/07/2014  1:14 pm  Show Profile   Bookmark this reply Add keepcalmandcoinon to your friends list Get a Link to this Reply
I use a hammer.
Pillar of the Community
noD's Avatar
United States
1584 Posts
 Posted 05/07/2014  5:10 pm  Show Profile   Bookmark this reply Add noD to your friends list Get a Link to this Reply
Thanks for the tip.
Pillar of the Community
edweather's Avatar
United States
7375 Posts
 Posted 05/07/2014  6:18 pm  Show Profile   Bookmark this reply Add edweather to your friends list Get a Link to this Reply
Yeah, now I use a towel underneath. The soft surface underneath let's the coin go into the folder. Contrary to what I originally thought, that a hard surface was optimum, I just ended up with a bruised thumb.
Pillar of the Community
52Raymo's Avatar
United States
8516 Posts
 Posted 05/07/2014  8:23 pm  Show Profile   Check 52Raymo's eBay Listings Bookmark this reply Add 52Raymo to your friends list Get a Link to this Reply

Quote:
I use a hammer.


Crisco works well too...
Oregon coin geek.....*** GO BEAVS ! ! ! ***
Bedrock of the Community
United States
20753 Posts
 Posted 05/08/2014  09:24 am  Show Profile   Bookmark this reply Add just carl to your friends list Get a Link to this Reply
Take a slightly larger coin that is required for the slot. Place on an angle in one corner of the slot and push. Turning the coin so it slowly enlarges the slot on all sides. This should make the slot larger and allow the normal coin to simply fall in place.
However, remember that the reason for the tight fit is that the slots are tapered. This means the top of the slot is smaller than the bottom. This is why once a coin is finally put into place, it stays there. If you enlarge the slot, as I explained, the coins are likely to simply fall out.
  Previous TopicReplies: 5 / Views: 1,511Next Topic  

To participate in the forum you must log in or register.



    




Disclaimer: While a tremendous amount of effort goes into ensuring the accuracy of the information contained in this site, Coin Community assumes no liability for errors. Copyright 2005 - 2026 Coin Community Family- all rights reserved worldwide. Use of any images or content on this website without prior written permission of Coin Community or the original lender is strictly prohibited.
Contact Us  |  Advertise Here  |  Privacy Policy / Terms of Use

Coin Community Forum © 2005 - 2026 Coin Community Forums
It took 0.21 seconds to rattle this change. Forums