| Author |
 Replies: 16 / Views: 2,191 |
Page 2 of 2
|
|
|
|
Bedrock of the Community
 United States
12477 Posts |
It's a high point because of the displaced metal to the right of it (gouge).
You can follow the damage to the rim where it is less severe and obviously incuse.
Just damage, I'll say.
In Memory of Crazyb0 12-26-1951 to 7-27-2020
In Memory of Tootallious 3-31-1964 to 4-15-2020
In Memory of T-BOP 10-12-1949 to 1-19-2024
|
|
Pillar of the Community
United States
1602 Posts |
I'm not so sure about that Spruette. It's awfully linear to be just displaced metal from that gouge. My two bits are on a die crack with damage after minting. Or possibly a really messed up die with fragments rearranged to cause the gouge as well. Just something to think about.  |
|
CCF Advertiser
United States
1533 Posts |
Needs more high mag pictures to be sure.
|
|
Pillar of the Community
United States
8518 Posts |
Looks like a gouge that pushed up metal. Need better pics though.
Oregon coin geek.....*** GO BEAVS ! ! ! ***
|
|
Pillar of the Community
United States
3058 Posts |
I agree with spuett, 52raymo, and Andrew.
|
|
Moderator
 United States
54283 Posts |
It would be very unusual for a die crack to be that long and in particular -- that straight. It would be very common for a coin to receive damage from something straight. The red box outlines what is clearly a gouge that pushed up metal, and the green box outlines separate smaller gouges that did not push up metal.  |
|
Bedrock of the Community
United States
94367 Posts |
 Completely. |
|
Pillar of the Community
 United States
3479 Posts |
I would agree nss-52 but the mark disappears from the cloth draped over her arm (which is a higher point) then reemerges into her arm pit.
|
|
Bedrock of the Community
United States
12477 Posts |
Can you get a clearer close-up of the area?
In Memory of Crazyb0 12-26-1951 to 7-27-2020
In Memory of Tootallious 3-31-1964 to 4-15-2020
In Memory of T-BOP 10-12-1949 to 1-19-2024
|
|
Pillar of the Community
United States
3479 Posts |
I'll try. I'm using my iPhone. I probably need to buy a good camera. Any suggestions?
|
|
Pillar of the Community
United States
6394 Posts |
Keep in mind that old scratches with displaced metal change their appearance as the scratched coin circulates. The high points wear down which can reduce or eliminate those portions of the scratch that pass over higher-relief areas. This is plain old PMD which has reduced the coin to "junk" silver status.  |
|
Pillar of the Community
United States
6370 Posts |
|
|
Bedrock of the Community
United States
94367 Posts |
Agree, basically junk silver.  |
|
Pillar of the Community
United States
3479 Posts |
Guys, I know it's junk silver. I only paid $7 for it. I'm just curious what caused the defect.
|
|
Bedrock of the Community
United States
12477 Posts |
I've been thinking on what would cause that gouge on the interior but leave shallower marks as well, especially on the rim. I think some sort of rotary tool/wheel and the gouge was the starting point and then it lost control and skipped over the surface two times and lastly on the rim. That could explain the metal displacement through heat, the nearly perfect linear pattern and the three smaller marks of slight contact. In Memory of Crazyb0 12-26-1951 to 7-27-2020
In Memory of Tootallious 3-31-1964 to 4-15-2020
In Memory of T-BOP 10-12-1949 to 1-19-2024
|
|
Page 2 of 2
|
Replies: 16 / Views: 2,191 |
Page 2 of 2
|
First Page
Posted 03/01/2017 11:28 pm
