| Author |
 Replies: 11 / Views: 870 |
|
|
Pillar of the Community
United States
2731 Posts |
|
|
|
|
Bedrock of the Community
United States
94367 Posts |
Nice one, well photographed.
|
|
Pillar of the Community
 United States
7174 Posts |
Nice find. These are fun to find.
|
|
Bedrock of the Community
United States
19143 Posts |
|
|
Pillar of the Community
 United States
2731 Posts |
Thanks gang!
"Pride is yoked with callous behavior, as humility is with compassion." St. Gregory Palamas Top Finds - 1969-S 1c FS-101 http://goccf.com/t/477681 1976 D WQ FS-101 http://goccf.com/t/382777 - 1968 D 1c FS-801 http://goccf.com/t/422254Cool clashed dies - 1972 D 1c http://goccf.com/t/429855&SearchTerms=CCLStruck-In Rim Burr - 1969 S 1c http://goccf.com/t/425587&SearchTerms=burrFloating (Type II) Counterclash - 1978 D 1c http://goccf.com/t/434991&SearchTerms=1978 |
|
Pillar of the Community
United States
3402 Posts |
Nice one...very striking de-lam.
KK
|
|
Pillar of the Community
United States
1204 Posts |
Great photos. I like the look of those small but significantly placed lams.
|
|
Bedrock of the Community
United States
62064 Posts |
Glad it wasn't on a Variety coin. A variety collector would view this as a problem coin and an error collector would not care to offer more it is were a variety. So in the case, I'm glad it wasn't a variety coin. (Two types of collectors for these if it were a variety, but it doesn't add an additional premium for both if that were the case)
|
|
Moderator
United States
95443 Posts |
Lams are very fun to find  . Too bad the new coins are zinc now..  Edited by Dearborn
08/14/2022 7:25 pm
|
|
Pillar of the Community
United States
4618 Posts |
Nice one! On a side note, this is known as a lamination, not a de-lamination. I personally think that de-lamination is a better identifier, but lamination is the accepted term for this in the numismatic world.  ANA ID: 3203813 - CONECA ID: N-5637 Clean a coin that may be worth collecting? Please DON'T! When in doubt, leave it dirty!! 
Edited by Yokozuna
08/14/2022 11:22 pm
|
|
Pillar of the Community
United States
2731 Posts |
Thanks again for the comments, yes Yokozuna, I am aware of the dueling defining terms of this error and so I try to use both whenever I post one :)
"Pride is yoked with callous behavior, as humility is with compassion." St. Gregory Palamas Top Finds - 1969-S 1c FS-101 http://goccf.com/t/477681 1976 D WQ FS-101 http://goccf.com/t/382777 - 1968 D 1c FS-801 http://goccf.com/t/422254Cool clashed dies - 1972 D 1c http://goccf.com/t/429855&SearchTerms=CCLStruck-In Rim Burr - 1969 S 1c http://goccf.com/t/425587&SearchTerms=burrFloating (Type II) Counterclash - 1978 D 1c http://goccf.com/t/434991&SearchTerms=1978 |
|
Pillar of the Community
United States
3402 Posts |
Quote:
I personally think that de-lamination is a better identifier  ...because that is exactly what is happening...the planchet material when it was being made had impurities that didn't allow for it to properly "laminate" (think atomic layers)...the subsequent pulling apart of this material is correctly defined as "de-lamination"... Think of a 1960's table top that has "Formica" brand laminate, laminated (the process of joining together) to the substrate with contact cement...When pieces on the edge pull of, they are termed to have de-laminated...can happen with wood veneers also. That is the term I will always use...the correct one...whether anyone else uses it or not . KK |
| |
Replies: 11 / Views: 870 |
|
Posted 08/13/2022 6:05 pm
